Movement Module - Revision history

Ian at 09:56, 25 April 2025

2025-04-25T09:56:19Z

Ian: N5 first version.

2025-03-24T10:42:02Z

N5 first version.

Ian at 14:59, 20 October 2020

2020-10-20T14:59:30Z

Ian at 09:27, 10 September 2020

2020-09-10T09:27:07Z

Ian at 10:33, 13 May 2020

2020-05-13T10:33:27Z

Ian at 14:45, 30 April 2020

2020-04-30T14:45:07Z

Ian: Created page with "In Infinity CodeOne, movement allows troopers to get around the game board. This section details all necessary rules to perform such movements. Movement takes place within th..."

2020-03-27T16:35:07Z

Created page with "In Infinity CodeOne, movement allows troopers to get around the game board. This section details all necessary rules to perform such movements. Movement takes place within th..."

New page

In Infinity CodeOne, movement allows troopers to get around the game board. This section details all necessary rules to perform such movements.

Movement takes place within the normal [[Order Expenditure Sequence]].

The Movement Attribute (MOV) from the [[Unit Profile]] indicates the amount of inches this Trooper can move with an Order. The MOV Attribute usually has two values: the first time the Trooper moves in an Order, and the second.

== [[Moving and Measuring]] ==
You can measure Movement distances immediately after declaring any ''Skill'' with the ''Movement'' [[Label]] and before determining where the Trooper ends his Movement, always measuring from the same point on the base’s outer edge and underside. [[Moving and Measuring|[...]]]

== [[Move]] ==
Common Skill that allows the user to move about the battlefield. [[Move|[...]]]

== [[General Movement Rules]] ==
When moving Troopers around the battlefield, players must measure the complete route (including, for example, any detour to avoid obstacles) and must always use the same part of the base for their measurements. [[General Movement Rules|[...]]]

== [[Prone]] State ==
During the Deployment Phase, players may deploy one or more of their Troopers Prone by placing a Prone Token beside them. [[Prone|[...]]]

== [[Jump]] ==
This Common Skill allows the user to clear obstacles and leap over small distances. [[Jump|[...]]]

== [[Climb]] ==
This Common Skill allows the user to scale heights and move up and down vertical surfaces. [[Climb|[...]]]

[[Category: Main Sections]]

@@ Line 7: / Line 7: @@
 Movement takes place within the normal [[Order Expenditure Sequence]].
-The Movement Attribute (MOV) from the [[Unit Profile]] indicates the number of inches this Trooper can move with an Order. The MOV Attribute usually has two values: the first time the Trooper moves in an Order, and the second.
+The [[Unit_Profile#Movement_.28MOV.29 | Movement Attribute (MOV)]] from the [[Unit Profile]] indicates the number of inches this Trooper can move with an [[Order]]. The MOV Attribute usually has two values: the first time the Trooper moves in an Order, and the second.
 [[Category: Main Sections]]

@@ Line 1: / Line 1: @@
 {{section-main-sections}}
-{{section-movement-module}}
+{{n5-section-movement-module}}
@@ Line 8: / Line 8: @@
 The Movement Attribute (MOV) from the [[Unit Profile]] indicates the number of inches this Trooper can move with an Order. The MOV Attribute usually has two values: the first time the Trooper moves in an Order, and the second.
 [[Category: Main Sections]]

@@ Line 1: / Line 1: @@
 {{section-main-sections}}
@@ Line 10: / Line 11: @@
 == [[Moving and Measuring]] ==
-You can measure Movement distances immediately after declaring any ''Skill'' with the ''Movement'' [[Label]] and before determining where the Trooper ends his Movement, always measuring from the same point on the base’s outer edge and underside. [[Moving and Measuring|[continued...]]]
+You can measure Movement distances immediately after declaring any ''Skill'' with the ''Movement'' [[Label]] and before determining where the Trooper ends his Movement, always measuring from the same point on the base’s outer edge and underside. [[Moving and Measuring | [read more...] ]]
 == [[Move]] ==
-Common Skill that allows the user to move about the battlefield. [[Move|[continued...]]]
+Common Skill that allows the user to move about the battlefield. [[Move | [read more...] ]]
 == [[General Movement Rules]] ==
-When moving Troopers around the battlefield, players must measure the complete route (including, for example, any detour to avoid obstacles) and must always use the same part of the base for their measurements. [[General Movement Rules|[continued...]]]
+When moving Troopers around the battlefield, players must measure the complete route (including, for example, any detour to avoid obstacles) and must always use the same part of the base for their measurements. [[General Movement Rules | [read more...] ]]
 == [[Prone]] State ==
-During the Deployment Phase, players may deploy one or more of their Troopers Prone by placing a Prone Token beside them. [[Prone|[continued...]]]
+During the Deployment Phase, players may deploy one or more of their Troopers Prone by placing a Prone Token beside them. [[Prone | [read more...] ]]
 == [[Jump]] ==
-This Common Skill allows the user to clear obstacles and leap over small distances. [[Jump|[continued...]]]
+This Common Skill allows the user to clear obstacles and leap over small distances. [[Jump | [read more...] ]]
 == [[Climb]] ==
-This Common Skill allows the user to scale heights and move up and down vertical surfaces. [[Climb|[continued...]]]
+This Common Skill allows the user to scale heights and move up and down vertical surfaces. [[Climb | [read more...] ]]
 {{section-main-sections}}

@@ Line 2: / Line 2: @@
-In Infinity CodeOne, movement allows troopers to get around the game board. This section details all necessary rules to perform such movements.
+In Infinity, movement allows troopers to get around the game board. This section details all necessary rules to perform such movements.
 Movement takes place within the normal [[Order Expenditure Sequence]].
-The Movement Attribute (MOV) from the [[Unit Profile]] indicates the amount of inches this Trooper can move with an Order. The MOV Attribute usually has two values: the first time the Trooper moves in an Order, and the second.
+The Movement Attribute (MOV) from the [[Unit Profile]] indicates the number of inches this Trooper can move with an Order. The MOV Attribute usually has two values: the first time the Trooper moves in an Order, and the second.